At the height of spring, it’s not just lovely peonies and roses coming into bloom. This time of year also brings a surge in less welcome growth: weeds.

Few things make a patio or walkway look untidy faster than weeds sprouting between paving stones. And if you only focus on removal, weeds will keep returning. The long-term solution is to properly seal the gaps between patio pavers.

While removing weeds and preventing regrowth takes a little time and effort upfront, the results can last for a while and dramatically improve the look of your outdoor space.

Ahead, we’ve asked an expert to share the most effective way to clear weeds from your paving—and keep them at bay.

Start by Removing Existing Weeds

close up low angle view of vibrant green wild grass and weeds sprouting between weathered grey stone pavers on a pathway during sunrise.pinterest
Muchlas Mahfuddin//Getty Images

First, you need to create a clean slate by removing all existing weeds. John Whitney, director of South Wales–based garden buildings and landscaping company Eden Landscapes, recommends a wire brush or a specialist knife for this task.

“A stiff-bristled wire brush or a patio knife dragged along the joints is the most effective manual method and gives you a clean start,” he says. “For larger areas, a pressure washer or the ‘jet’ or ‘stream’ setting on a hose nozzle can blast out both the weeds and the old jointing material efficiently without damaging the slabs.”

senior woman clearing moss and small weeds from between the pavers in her garden path.pinterest
Peter Burnett//Getty Images

White vinegar or a diluted salt solution can also work wonders, especially on young weeds, although, as John notes, you’ll likely have to apply it a few times to be effective, and it won’t kill established root systems.

Another household remedy, but one that the expert cautions against, is scalding unwanted plants with boiling water. Although effective in removing them, the heat can compromise the integrity of the pointing mortar between slabs over time.

Next, Prevent Weeds from Growing Back

The only way to reliably keep weeds from coming back is to seal the cracks. “Once the joints are clear, the best long-term solution is to repoint with a quality polymeric jointing sand or a brush-in mortar compound,” John says. “These set firm when wet and create a dense, weed-resistant joint that does not give seeds anywhere to germinate.”

This, he says, won’t just keep weeds at bay but also give your patio or terrace a more finished look. You can also consider sealing the entire surface with a patio sealant afterwards to add another layer of protection and make the slabs easier to clean.

Below, read John’s step-by-step guide to achieve the best results.

How to Apply Polymeric Jointing Sand

full bucket of polymeric paver sand with trowel on top of gray concrete patio stone paver walkway.pinterest
Trong Nguyen Photo//Getty Images
  1. Clean the patio thoroughly and make sure the surface is dry: Remove weeds, old jointing material, and debris from the joints using a wire brush or patio knife. Polymeric sand should only be applied to a dry surface.
  2. Pour the sand over the patio and brush it into the joints: Spread it evenly across the surface, then use a stiff brush and sweep back and forth until the gaps are filled to just below the surface of the slabs.
  3. Remove all excess sand and compact it: Carefully brush or blow residue off the slab surfaces. Any sand left on top can create a haze once wet. Then use a plate compactor or firmly tamp the slabs to help the sand settle into the joints.
  4. Mist with water and leave to cure: Use the fine mist setting on the hose nozzle to gently spray the whole area—this activates the binding agent. Keep off the patio for 24 hours and check the weather forecast to ensure no heavy rain during this period.

Apply Patio Sealant, if Desired

workers are applying waterproofing with a brush. the roof system of a high rise buildingpinterest
Rattankun Thongbun//Getty Images
  1. Start with a clean, dry surface: If you’ve applied polymeric sand, allow it to cure for the full 24 hours before sealing. Sweep away dust, loose material, debris, and make sure the surface is dry.
  2. Apply the sealant in small sections: Use a roller or wide brush to work the sealant into the surface, being careful to avoid puddles in low spots. Also, keep a wet edge to avoid lap marks.
  3. Apply a second coat if needed: Most sealants require two coats. Apply the second once the first is dry to the touch, usually after two to four hours, depending on the temperature.
  4. Allow the sealant to cure: Keep off the patio for 24 hours and check the weather forecast to ensure no rain during this period.

Follow these tips to enjoy a weed-free patio or terrace this season and beyond.

Headshot of Wanda Sachs
Wanda Sachs
Multiplatform Writer

Wanda Sachs is the Multiplatform Writer for Country Living and House Beautiful, exploring the latest in gardening, wildlife and sustainable living alongside interiors and property. She is particularly interested in human-interest stories, the intersection of design and pop culture, and the evolving relationship between urban and rural life. Previously, she served as Associate Editor at The Berliner in Berlin, where she reported on culture and fashion. Wanda studied English and German at the Goethe University Frankfurt and Exeter University.